Product Overview
SI-2100 | 2 Channel Amplifier
Two Chan, Digital Power Amp; 2 x 100W; 400W Bridged; Rack Ears Incl.; 110/240V
Whats in the box
- Stereo system integration amplifier
- 6' AC power cord (3-prong IEC plug)
- 2 Rack-mount ears
- Installation Guide
Overview: The Niles Audio SI (System Integration) Amplifiers are designed to power your custom-installed Audio-Video system. They are constructed with the finest materials available, including 1% metal film resistors, high quality capacitors, and oversized heat sinks, that can properly cool the unit without the need for a noisy fan.
Power Output: The SI-2100 stereo amplifier provides 100 watts RMS per channel at 8 ohms, and 225 watts RMS per channel at 4 ohms with all channels driven. When bridged, the output is 400 watts into 8 ohms.
Line Level Input: The amplifier has a single pair of gold-plated stereo RCA input jacks. If you are bridging the amplifier, you can connect a mono source (single RCA) to the left-channel input.
Cascade Audio Outputs: The unit's Cascade Audio Outputs enable you to daisy-chain another amplifier, by connecting the preamp output of the SI-2100 to the input of the second amplifier. The outputs are not buffered, so if you wish to daisy-chain more than 5 Niles SI Amplifiers, you will need a buffered distribution amplifier, such as the Niles AVDA-3.
Speaker Terminals: The amplifier is equipped with 5-way binding post speaker terminals. The terminals will accept single- and dual-banana plugs, pin connectors, spade lugs, and bare wire up to 12-gauge. For most applications, 16- or 18-gauge wire is recommended. For wiring runs longer than 80 feet, 14-gauge wire is recommended.
Multiple Speaker Loads: The SI-2100 is stable into very low impedance loads (minimum impedance is 2.66 ohms in stereo), which means you can safely operate up to three pairs of 8-ohm speakers directly connected to the amplifier. You will need to connect a speaker selector switch if you wish to independently turn on/off connected speakers, or if you wish to connect more than three pairs of speakers.
Independent Level Controls: The SI-2100 has independent left- and right-channel level controls, letting you pre-set the maximum volume, or precisely match the volume to the rest of the system. The controls are located on the rear panel to limit unwanted access.
Turn-on Modes: For convenience, the SI-2100 offers three turn-on modes. Using the 3-way switch on the back panel, you can choose from the following modes:
- Manual Turn-on: The amplifier is turned on and off using the front panel Master power switch. The automatic turn-on circuitry is turned off. (Switch position: Constant)
- Music Sense: The amplifier turns on automatically when the presence of an audio signal is detected on either the left or right input. When the audio signal is no longer detected, the amplifier turns itself off after approximately 2 minutes. (The front panel Master switch must be in the On position, and the Turn-on Mode switch position is set to Audio Sense.)
- External Trigger: The amplifier turns on automatically when a signal is detected at the 3.5mm AC/DC trigger input. Once the Trigger voltage is turned off, the amplifier automatically turns itself off. Voltage triggers can be supplied by a variety of sources, including surround sound processors, video projectors, and automated switchers. The trigger signal must be 3-24 volts AC or DC, 20 mA or greater. (The front panel Master switch must be in the On position, and the Turn-on Mode switch position is set to 3-30V AC/DC Trigger Input.)
12-volt Control Output: In addition to the 12-volt Trigger Input, the SI-2100 can be used to control other devices using 12-volt triggers, such as motorized screens and curtains. When the amplifier is powered on, a 12-volt DC (150 mA) signal is present at the 12V Control Out 3.5mm mini-jack. (Polarity: tip = +)
Rack-mount Ears: The SI-2100 comes with a pair of rack-mount ears to allow you to mount the amplifier in a standard equipment rack. The rack ears attach to the sides of the amplifier chassis using the 4 installed screws. The amp requires only a single rack space (1U) with the feet removed.
